hae75w series half-brick dc-dc converter 4:1 ultra wide input range up to 75watts features applications ? no minimum load required ? 3000vac reinforced insulation for 110vin 2250vdc basic insulation for 24vin and 48vin ? ul60950-1, en60950-1, iec60950-1, & en50155 safety approvals ? ce marked ? compliant to rohs ii & reach ? railway system ? wireless network ? telecom/datacom ? industry control system ? distributed power architectures ? semiconductor equipment 3000vac isolation 2250vdc isolation remote control uvp ocp scp ovp otp technical specification all specifications are typical at nominal input, ful l load and 25 otherwise noted input range output voltage output current @full load input current @ no load efficiency maximum capacitor load model number vdc vdc a ma % f hae75-24s3p3w 9 ~ 36 3.3 20 85 87 60600 hae75-24s05w 9 ~ 36 5 15 120 88 30000 hae75-24s12w 9 ~ 36 12 6.3 185 88 5250 hae75-24s15w 9 ~ 36 15 5 185 88 3330 hae75-24s24w 9 ~ 36 24 3.2 85 87 1330 hae75-24s28w 9 ~ 36 28 2.7 85 87 960 hae75-24s48w 9 ~ 36 48 1.6 85 87 330 hae75-48s3p3w 18 ~ 75 3.3 20 60 88 60600 hae75-48s05w 18 ~ 75 5 15 60 90 30000 hae75-48s12w 18 ~ 75 12 6.3 90 90 5250 hae75-48s15w 18 ~ 75 15 5 50 89 3330 hae75-48s24w 18 ~ 75 24 3.2 50 88 1330 hae75-48s28w 18 ~ 75 28 2.7 50 88 960 hae75-48s48w 18 ~ 75 48 1.6 50 87 330 HAE75-110S3P3W 43 ~ 160 3.3 20 10 89 60600 hae75-110s05w 43 ~ 160 5 15 10 91 30000 hae75-110s12w 43 ~ 160 12 6.3 10 91 5250 hae75-110s15w 43 ~ 160 15 5 10 91 3330 hae75-110s24w 43 ~ 160 24 3.2 10 90 1330 hae75-110s28w 43 ~ 160 28 2.7 10 90 960 hae75-110s48w 43 ~ 160 48 1.6 10 90 330 part number structure hae75 - 48 s 05 w - p th hs series name input output output input ctrl and through hole assembly option voltage quantity voltage range pin options type (1) (vdc) (vdc) 24: 9~36 s: single 3p3: 3.3 4:1 : negative logic, : thread : no heat-sink 48: 18~75 05: 5 0.200" pin length th: no thread heat-sink type: 110: 43~160 12: 12 l: negative logic, hs: height h=0.45? vertical fin, 15: 15 0.145" pin length 7g-0021a-f 24: 24 p: positive logic, hs1: height h=0.24? horizontal fin, 28: 28 0.200" pin length 7g-0022a-f 48: 48 s: positive logic, hs2: height h=0.24? vertical fin, 0.145"pin length 7g-0023a-f hs3: height h=0.45? horizontal fin, 7g-0024a-f terminal block type (2) : t: wall mounted tf: wall mounted with emc filter (3) tf1: wall mounted with emc filter can be connected to pe (3) (1) the module can?t equip heat-sink with th option . (2) terminal block type only for 0.200? pin length. (3) emi filter meet en55011, en55022 class a.
hae75w input specifications parameter conditions min. typ. max. unit operating input voltage range 24vin(nom) 48vin(nom) 110vin(nom) 9 18 43 24 48 110 36 75 160 vdc start up voltage 24vin(nom) 48vin(nom) 110vin(nom) 9 18 43 vdc shutdown voltage 24vin(nom) 48vin(nom) 110vin(nom) 7.5 16 36 vdc start up time constant resistive load power up remote on/off 110vin(nom) others 110vin(nom) others 60 25 60 25 ms input surge voltage 1 second, max. 24vin(nom) 48vin(nom) 110vin(nom) 50 100 185 vdc input filter (1) pi type negative logic (standard) dc-dc on dc-dc off short or 0 ~ 1.2vdc open or 3 ~ 12 vdc referred to ?vin pin positive logic (option) dc-dc on dc-dc off open or 3 ~ 12 vdc short or 0 ~ 1.2vdc remote on/off input current of ctrl pin -0.5 1 ma remote off input current 3 ma output specifications parameter conditions min. typ. max. unit voltage accuracy -1.0 +1.0 % line regulation low line to high line at full load -0.1 +0.1 % load regulation no load to full load -0.1 +0.1 % voltage adjustability maximum output deviation is i nclusive of remote sense -20 +10 % remote sense % of vout(nom) if remote sense is not being used, sense pins shoul d be connected to corresponding polarity output pins. 10 % ripple and noise measured by 20mhz bandwidth with a 4.7 f/50v x7r mlcc with a 4.7 f/50v x7r mlcc with a 4.7 f/50v x7r mlcc with a 2.2 f/100v x7r mlcc 3.3vout, 5vout 12vout, 15vout 24vout, 28vout 48vout 75 100 200 300 100 125 250 350 mvp-p temperature coefficient -0.02 +0.02 %/ transient response recovery time 25% load step change 200 250 s over voltage protection % of vout(nom); hiccup mode 115 130 % over load protection % of iout rated; hiccup mode 110vin(nom) others 110 150 140 % short circuit protection continuous, automatics recovery general specifications parameter conditions min. typ. max. unit 1 minute (reinforced insulation) 110vin(nom) input to output input (output) to case 3000 1500 vac isolation voltage 1 minute (basic insulation) others input to output input (output) to case 2250 1600 vdc isolation resistance 500vdc 1 g isolation capacitance 2500 pf switching frequency 270 300 330 khz safety approvals ul60950-1 en60950-1 iec60950-1 en50155 case material 24vin(nom) and 48vin(nom) 110vin(nom) metal aluminum base-plate with plastic case base material 24vin(nom) and 48vin(nom) fr4 pcb potting material silicone (ul94 v-0) weight 97g (3.42oz) mtbf mil-hdbk-217f, full load 3.36210 5 hrs
hae75w environmental specifications parameter conditions min. typ. max. unit operating case temperature base-plate -40 +105 over temperature protection +115 storage temperature range terminal block type others -40 -55 +105 +125 thermal impedance (2) vertical direction by natural convection (20lfm) module without assembly option heat-sink type with 0.24" height heat-sink type with 0.45" height 6.7 5.4 4.7 /w thermal shock mil-std-810f shock en61373, mil-std-810f vibration en61373, mil-std-810f relative humidity 5% to 95% rh emc specifications parameter conditions level emi (3) en55011, en55022 class a class b esd en61000-4-2 air 8kv and contact 6kv perf. criteria a radiated immunity en61000-4-3 20v/m perf. criteria a fast transient (4) en61000-4-4 2kv perf. criteria a surge (4) en61000-4-5 en55024 2kv and en50155 2kv perf. c riteria a conducted immunity en61000-4-6 10vr.m.s perf. criteria a note: 1. input source impedance: the power modules will oper ate as specifications without external components, assuming that the source voltage has a very low impedance and reasonable input voltage reg ulation. highly inductive source impedances can aff ect the stability of the power module. since real-world voltage source has finite impedanc e, performance can be improved by adding external f ilter capacitor. the hae75-24s w recommended 4.7 f/50v x7r mlcc or nippon chemi-con ky series, 68 f /100v or better capacitor. 2. (1)thermal test condition with vertical direction b y natural convection (20lfm). (2)the heat-sink is optional and p/n: 7g-0021a-f , 7g-0022a-f , 7g-0023a-f , 7g-0024a-f. please refer to heat-sink selection guide. 3. the standard modules meet emi class a or class b wi th external components. for further information, pl ease contact with p-duke. 4. an external input filter capacitor is required if t he module has to meet en61000-4-4, en61000-4-5. the hae75-24s w and hae75-48s w recommended 2 pcs of aluminum electrolytic capaci tor (nippon chemi-con ky series, 220 f/100v) to connect in parallel. the hae75-110s w recommended 2 pcs of aluminum electrolytic capaci tor (nippon chemi-con kxj series, 150 f/200v) to connect in parallel. 5. case grounding connecting four screw bolts to shield plane will he lp to reduce the emi. 6. for further information, please contact with p-duke . caution: this power module is not internally fused. an input line fuse must always be used. characteristic curve 0 20 40 60 80 100 120 -40 -20 0 20 40 60 80 100 120 ambient temperature,ta( ) output power(%) dc/dc module only natural convection (20lfm) 100lfm 200lfm 300lfm 400lfm 500lfm mount on 2u iron base-plate (dimension 19? x 3.5? x 0.063?) natural convection (20lfm) terminal block natural convection (20lfm) 0 20 40 60 80 100 120 -40 -20 0 20 40 60 80 100 120 ambient temperature,ta( ) output power(%) natural convection (20lfm) 100lfm 200lfm 300lfm 400lfm 500lfm 0 20 40 60 80 100 120 -40 -20 0 20 40 60 80 100 120 ambient temperature,ta( ) output power(%) natural convection (20lfm) 100lfm 200lfm 300lfm 400lfm 500lfm hae75-48s05w derating curve (note 2) hae75-48s05w derating curve (note 2) with 0.24? height heat-sink hae75-48s05w derating curve (note 2) with 0.45? height heat-sink 60 66 72 78 84 90 96 18 24 30 36 42 48 54 60 66 72 75 input voltage(v) efficiency(%) iout= 100% f.l iout= 50% f.l iout= 25% f.l 36 46 56 66 76 86 96 10 20 30 40 50 60 70 80 90 100 % of full load efficiency(%) vin= 18v vin= 24v vin= 48v vin= 75v hae75-48s05w efficiency vs. input voltage hae75-48s 05w efficiency vs. output load
hae75w heat-sink type options vertical fin orientation, suffix:-hs, -hs2 horizont al fin orientation, suffix:-hs1, -hs3 hs: height h=0.45? vertical fin, 7g-0021a-f hs1: height h=0.24? horizontal fin, 7g-0022a-f hs2: height h=0.24? vertical fin, 7g-0023a-f hs3: height h=0.45? horizontal fin, 7g-0024a-f 1. all dimensions in inch (mm) 2. tolerance :x.xx0.02 (x.x0.5) x.xxx0.01 (x.xx0.25) terminal block type option wall mounted, suffix: -t wall mounted with emc filter, suffix: -tf wall mounted with emc filter, suffix: -tf1 (can be connected to pe ) terminal block type -t -tf -tf1 weight 200g (7.05oz) 280g (9.88oz) 287g (10.12oz) dimensions 3.35 x 2.40 x 1.10 inch (85.0 x 61.0 x 2 8 0mm) 3.35 x 2.40 x 1.47 inch (85.0 x 61.0 x 37.3 mm) 3.35 x 2.40 x 1.53 inch (85.0 x 61.0 x 38.8 mm) through hole (wl) 2.126 x 3.071 inch (54.00 x 78.0 0 mm), 4- 0.17 inch ( 4.3mm) for more detail information, please contact with p- duke. m echanical d rawing hae75-24s w, hae75-48s w 1. all dimensions in inch (mm) 2. tolerance :x.xx0.02 (x.x0.5) x.xxx0.01 (x.xx0.25) 3. pin pitch tolerance 0.01 (0.25) 4. pin dimension tolerance 0.004(0.1) 5. mounting screws should always be used. 6. the screw locked torque: max 5.0kgf-cm(0.49n-m) hae75-110s w 1. all dimensions in inch (mm) 2. tolerance :x.xx0.02 (x.x0.5) x.xxx0.01 (x.xx0.25) 3. pin pitch tolerance 0.01 (0.25) 4. pin dimension tolerance 0.004(0.1) 5. mounting screws should always be used. 6. the screw locked torque: max 3.5kgf-cm(0.34n-m) pin connection pin define diameter 1 -vin 0.04 inch 2 case 0.04 inch 3 ctrl 0.04 inch 4 +vin 0.04 inch 5 -vout 0.08 inch 6 -sense 0.04 inch 7 trim 0.04 inch 8 +sense 0.04 inch 9 +vout 0.08 inch external output trimming output can be externally trimmed by using the method shown below. ?? ? ?? ? ? ? = k 2 % 100 r d ( ) ( ) ?? ? ?? ? ? ? + ? ? ? + = k % % 2 100 % 225 .1 % 100 v r out u
|
